What is SeaDek?

Durable and shock absorbent, SeaDek provides not only an exceptional traction surface but also lessens the fatigue brought on from prolonged standing and working on hard decking and platforms. SeaDek also protects your deck from scratching, chipping and dents. Fishermen will appreciate SeaDek’s noise reducing qualities.

SeaDek is manufactured in the United States from nonabsorbent, closed cell EVA foam specifically formulated for marine applications. Sports fishing, sailing, ski boats, commercial marine, platforms and steps are just a few of the unlimited applications for SeaDek Non-Skid Marine Traction.

SeaDek’s pressure sensitive adhesive backing makes application a breeze. Just measure, cut peel and stick. It’s that easy!

How is SeaDek applied?

SeaDek is applied using a pre applied pressure sensitive adhesive (PSA).

Can SeaDek be applied over existing non-skid?

SeaDek adheres very well to most molded-in non-skids and properly applied and maintained aggregate type non-skid paints, as long as the surface is cleaned properly.

What colors are available?

Stock colors are caribbean blue, bimini blue, bahama blue, midnight black, olive green, seafoam green, storm gray, hatteras white, cool gray, beach sand, aqua camo, army camo, snow camo, mica, mocha, camel, faux teak: teak over black, titanium, teak over holly, holly over teak.

What is the best method to clean SeaDek?

SeaDek cleans easily with soap, hot water and a stiff brush.

What do I cut SeaDek with?

Use a fresh bladed razor knife. You may have to change blades depending on the size of the job and the amount of cuts made.

What is the cost per square foot?

Price is determined by material used and labor time.

What is the largest size I can order?

39″x77″ in sheet form.

What is the life expectancy?

Five to seven years. Longer if the boat is stored inside.

What is the warranty?

SeaDek marine products are warranted to be free from any defects at the time of purchase. The EVA has a 36 month material and workmanship warranty. The PSA cannot be warranted due to many outside issues that may be present during installation.

Can I get a custom sized helm pad?

Yes, provide dimensions and a quote will be provided.

Can SeaDek sheets be seamed?

This is not recommended. Even with a very small shrink rate, a small gap between sheets will be present. We recommend leaving a 1/2 inch gap between panels.

How long will it stayed adhered?

If proper prepping has been done, you can expect at least 5-7 years of life.

Can it be re-adhered if necessary?

Yes, if the edge has slightly come up, use an acrylic based super glue. If the sheet has completely come up, you will have to clean the area thoroughly to remove any existing PSA and reapply another new sheet.

If I choose to remove the pad how do I do this?

Use a plastic putty knife to get under one corner. Grip and pull off. If the EVA seems to be sticking and tearing, use the putty knife to jab the area. You may want to enlist another set of hands to assist. Once the entire pad is removed, there will be a small amount of PSA left on the surface. Soak with mineral spirits for 10 minutes, scrap with the plastic putty knife. Once the PSA has been removed, use acetone to remove the mineral spirits.

Can you do custom logos?

Yes, we can engrave logos and text if supplied with vector graphic of logo or given desired text style.

Is the product pet friendly (dogs)?

Our product is made of an EVA foam material so if scratched at enough the product will tear or rip. The product is a closed cell foam so you shouldn’t have to worry about the product absorbing anything. We can not warranty if your pet tears up your pad/s.

What temperature is safe to apply new product at?

Above 60 degrees and dry is recommended.

Will the product stain?

If attended to promptly in most cases you should be OK. Fuel stabilizers, bird droppings, rust, and mustard are known to stain if not attended to in a timely manner.

What is the most popular two color pad choice?

Storm gray over black.